Share solution

If the ring tone problem in Nokia Asha 201 SOND quality is too low or poor voice quality in Ringer Nokia Asha 201 you can solve this problem easily with this schedule that is posted with this first step post.
 


in ringer to checked, so if it shows little or poor voice continuity put this ring as it does not show continuity ringer does not work and changing damage.after ringer ok you might not vote, these two main points ring is connected to the board control chart can be found in these two prints in red and blue lines on the Lcd lines.both two different paths.you should also check these links with the meter and if one of them is broken or damaged, you can easily can jumper, as defined in diagram.
for more detail and new tips and tricks about this problem keep visiting this page we will update it timely with new diagrams.some related post are also given bellow you can read them also for more information.

nokia 5130 battery connector ways

Heres the solution  that may help fix and repair Nokia 2700 classic Power problem. This solution is for Nokia 2700 classic that shows charging indication but doesnt  get On or power up when pressing the power key switch button.  Although this solution came late but  still there are many who are looking and requesting  this solution.
There is line test spots near the Keypad filter IC that can be easily check the power/ end key line paths, just apply a jumper wire if that line is open or cut.
If the said line spots is okay, you may need to check and replace the upper Keypad Filter IC.

Plug in Charging pin into charging jack of Nokia C2-06 and if it shows an indication message Charger Not Supported it can be due to these few parts that are given bellow in diagram.So after disassemble of Nokia C2-06 clean these parts and area with electronics cleaner.

Apply hot air and make it dry.Resold these parts indicated with red lines in above diagram to solve Charger Not Supported in Nokia C2-06
You can take these parts from other models of nokia also to solve charging problem in nokia C2-06 

As we know Nokia Asha 311 have keypad and touch Lcd both.So if you are facing touch Lcd problem in Nokia Asha 311 it can be solve with a few steps that i am going to describe in this post.Look at the diagram bellow and follow steps that are given in it.
In above diagram you can see touch pad jack and a few different color lines in it. In first step try calibration to solve touch Lcd problem if touch Lcd touch positions are not correct.Nokia C5 Handsfree Headset problem solution ways

If touch Lcd is totally not working you can replace with new one and if replacement of touch Lcd is not working that can be problem of touch pad ways.
In above diagram you can see touch pad tracks so check all these paths with meter and if any of them is missing apply jumpers as given in repairing diagram for Nokia Asha 311 touch Lcd.
for more detail and new tips and tricks about cellphone service problem keep visiting this page we will update cellphone service diagrams timely with new cellphone diagrams.some related post are also given bellow you can read them also for more information about cellphone.

Heres a full solution for a damaged Nokia 1280 ON and OFF key problem. This problem may result to unable the device to turns on but it shows charging indication when the battery charger is being plug-in.

The solution below shows the entire Nokia 1280 ON/OF key connection tracks which can be used for easy troubleshooting.


If the Nokia 1280 On-Off key may not working, you can trace its connection line paths as shown on solution above. Just apply a jumper wire if the line tracks is open or cut.

Heres  the solution for Nokia E90 (MIC) microphone or mouthpiece problem. This solution shows the connection line paths that needs to check or can be used as a guide where to put or apply a jumper wire if the microphones PCB terminal solder pads is already lifted or missing.

If encountered these problem on nokia e90, you may need to replace the Digimic  module (digital microphone).
But before that you may first check and trace the microphones supply voltage and clock line paths.
The solution below shows the particular spots or components where to start or check these corresponding connections on Nokia E90 microphones circuit



Just follow the spots where to check and test the microphones supply voltage and audio clock signal is is feeds from the power and audio IC (Avilma), the microphones data signal is feed to the application processor(RAPIDO).
If all the line paths is all okay you may then proceed in replacing the digital microphone module. 

 

If mic is not working in Nokia X2-05. Microphone solution with jumpers, Low voice of Nokia X2-05 mic problem solution, Nokia X2-02 mic jumpers to make it solve.Nokia X2-05 Speaker problem solution jumper ways

If mic is not working or have a low voice it can be fault of mic and housing. Check Nokia X2-05 housing ( body ). All housing have a small whole at the point of mic. In some cases rust or dust cover this point and the voice can not reach proper to the mic point so make it clean if there is some dust on it.
After disassambly of Nokia X2-05 look at the motherboard for rust carbon or burren parts. If you found some rust or carbon apply electronics cleaner on the mother board and apply hot air to make it dry proper.
Applying too much heat can damage the mother board and parts.It also can be harm for your skin.So keep in mind about normal heat flow when making it dry.
Remove mic and check all these tracks that are provided in above diagram to solve mic problem in Nokia X2-05. In diagram two different color lines are given to identify all parts that are used to solve Nokia X2-05 mic problem with jumpers.
If some parts are missing or damage apply jumper on these points where small circles are pointing in nokia mic repairing diagram above.

Nokia 100 101 LCD Display Solution Jumper Ways,Nokia 100 101 LCD Display Solution By Jumper,Nokia 100 101 LCD Display Solution,Nokia 100 101 LCD Display Problem.All these display problems can be cause of water damages, carbon and burn parts.
 

Parts may have been damaged. Keep checck all these tracks that are given in above diagram to solve display problems in nokia 100. If you find out missing parts replace them and if any tracks is not working then apply jumpers as shown in diagram.